No532Power AmplifierOwner’s Manual
6Mark LevinsonIf this case occurs, consider installing a dedicated AC circuit for the system. Contact a licensed electrician for assistance. If more t
7Nº532 Power AmplifierFront PanelThe front panel contains one LED and two buttons – Standby and Power – as shown. Power ButtonControls the AC power to
8Mark LevinsonStatus LEDIndicates the operating state of the Nº532 and provides basic diagnostic information if a fault condition occurs. The table be
9Nº532 Power AmplifierNote The audio outputs of this power amplifier are considered Class 2 (CL2) circuits in North America. This means the wire conne
10Mark LevinsonBanana plugs can also be used to connect the speaker cables to the loudspeaker binding posts. Banana plugs are not available on the 230
11Nº532 Power AmplifierLink2 PortsUses the Mark Levinson Link2 protocol to link together two or more Mark Levinson components. For more information on
12Mark LevinsonNote The Nº532 does not support wireless connection. However, a cable attached from the amplifier to a wireless adapter can be used to
13Nº532 Power AmplifierTo Connect Using a Router:1. Connect a network cable between the router and the Ethernet port on the rear panel of the Nº532.2.
14Mark LevinsonNote If you are putting more than one Nº532 power amplifier into the network, we recommend connecting and configuring the amplifiers on
15Nº532 Power Amplifier4. On the address line (URL), type “No532” and press Enter.If Internet Explorer is unable to find the amplifier, then you must
FCC NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
16Mark Levinson4. Click the Properties button to open the Local Area Connection Properties menu.Note If the computer is not currently connected to an
17Nº532 Power Amplifier4. Click the Properties button to open the Local Area Connection Properties menu.Note If the computer is not currently connecte
18Mark LevinsonFor the computer to find the Nº532, the TCPIP and LAN settings of the computer must be set up. Refer to the previous procedure, “Settin
19Nº532 Power AmplifierDirect ConnectionIf you are not using a router, use this procedure to connect directly to a computer. For the computer to find
20Mark LevinsonML NetThe ML Net protocol allows you to control two or more Mark Levinson products simultaneously via the Ethernet port. Note Since ML
21Nº532 Power AmplifierThe figure below illustrates a typical ML Net setup:Discovering SlavesBefore the master device can control any slave device, th
22Mark LevinsonML Net and Link2A system can use ML Net and Link2 together, but the Link2 control has priority. Status requests and notifications are s
23Nº532 Power AmplifierTroubleshootingIncorrect operation is sometimes mistaken for malfunction. If problems occur, use this section for troubleshooti
24Mark LevinsonNo Response toCommands in ML Net1. Verify that the master device and the Nº532 are properly connected together with a router.2. Verify
25Nº532 Power AmplifierFault ProtectionThe Nº532 is designed to prevent damage to itself and associated components. These extensive features protect b
iii1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Cl
26Mark LevinsonRestoring Factory DefaultsPressing the Factory Default button on the internal Web page of the amplifier resets all settings to their fa
27Nº532 Power AmplifierSpecificationsAll specifications are subject to change without notice.Input & Output Connectors •two balanced XLR inputs• t
28Mark LevinsonDeclaration of ConformityApplication of Council Directive(s):2004/108/EC and 2006/95/EC, as amended.Standard(s) to Which Conformity Is
ivMark LevinsonSafety Terms & SymbolsThese terms may appear in this manual:Warning! Calls attention to a procedure, practice, condition or the lik
1Nº532 Power AmplifierTable of ContentsIntroduction ... 2Product Description
2Mark LevinsonIntroductionThank you for purchasing the Nº532 Dual Monaural Power Amplifier. True to Mark Levinson® tradition, the audio excellence and
3Nº532 Power AmplifierSpecial care was taken in the design and placement of the voltage regulator circuitry. Using multiple stages, two types of regul
4Mark LevinsonProduct RegistrationRegister your Nº532 online at www.marklevinson.com within 15 days of purchase. Retain the original, dated sales rece
5Nº532 Power AmplifierDO allow at least 6 inches (15cm) of clearance behind the amplifier so that the power cord and cables have space to bend without
Comments to this Manuals